Heavy Equipment Guide Logo

The right hydraulic fluid provides more power while using less energy

Using an inefficient fluid in your hydraulic system is like having a flat tire – not only will it slow you down, it will increase the energy needed to power your equipment. 

In hydraulic equipment, the fluid is the medium for power transmission. Rotary power at the input shaft of a pump is converted to fluid power in the form of flow (kinetic energy) and pressure (potential energy). The resulting power is used to perform the work of moving cylinders and rotating hydraulic motors. 

The efficiency of this energy conversion is affected by flow and pressure losses within a machine. Flow losses, due to internal leakage through gaps in pumps, valves and motors, reduce the volume of fluid available to create machine motion. This decreases system efficiency.

Pressure losses, due to mechanical and fluid friction, reduce the linear and rotary force available to lift or move the payload. This increases energy consumption.

Putting fluid efficiency to the test 
Petro-Canada Lubricants teamed up with the Fluid Power Institute at Milwaukee School of Engineering to investigate how hydraulic fluids affect machine productivity and energy consumption.
 
In this study, a hydraulic dynamometer was used to evaluate fluid efficiency. It consisted of a variable displacement axial piston pump (Danfoss Series 45) and a fixed displacement hydraulic motor (Danfoss Series 90), plus directional and proportional control valves. This pump and motor combination is similar to a hydraulic system that might be found on the swing drive of an excavator, the propulsion system of a skid-steer, or the winch on a hydraulic crane. 

Two fluids were evaluated: a conventional, mineral oil-based monograde (3707) and Petro-Canada’s high performance HYDREX XV All Season (3708). HYDREX XV is a semi-synthetic, multigrade hydraulic fluid formulated with a shear stable polymer and carefully selected additives to maximize viscosity stability and fluid longevity. 

The fluids were tested at 50°C, 60°C, 80°C and 90°C. The hydraulic pump speeds were 800, 1,200 and 1,800 rpm, while the hydraulic motor speeds ranged from 1 to 600 rpm. The system pressure was regulated from 67 to 276 bar in 34 bar intervals by a proportional electrohydraulic compensator control. 

A total of 1,782 data points were collected for each fluid during this demonstration. 

Hydraulic motor torque, pump flow and system power losses were the key performance properties examined in this study. These three parameters quantify the energy inputs that do not produce work.
 
Higher friction = higher fuel consumption 
Motor torque losses were determined based upon the difference between the theoretical and measured torque output of the motor. 

At low speeds, torque losses are due to friction between moving surfaces.
 
At high speeds, a large volume of oil is required to rotate the hydraulic motor. This results in high pressures at the outlet of the motor, which reduces the torque available to move the load. 

HYDREX XV had 10 percent lower torque loss than the conventional monograde at 90°C. Reducing torque loss in a hydraulic machine could increase how far a skid steer pushes its bucket into a gravel pile or increase how deep a horizontal boring machine drives its augers into the ground, for example.

Lower flow = lower system efficiency 
Hydrostatic losses occur at constant gap interfaces, such as in directional and pressure compensator control valves. 

Hydrodynamic flow losses occur at moving gap interfaces, such as between the piston and cylinder wall. 

In both cases, flow losses have the greatest impact when the machine is operating at high pressures and temperatures. The monograde fluid showed higher average flow losses than HYDREX XV at 60°C, 80°C and 90°C. Reducing flow losses in a machine could increase the trenching speed of a backhoe loader, as an example.

Power loss is the difference between the input and output power of a hydraulic machine. Hydraulic systems are designed to minimize power losses so that the maximum amount of energy is converted into work. Typically, this is accomplished by regulating the input power of the pump through load-sensing or pressure compensator control. 

The monograde fluid showed higher losses than Petro-Canada Lubricants’ HYDREX XV (3708) at 276 bar. These losses not only reduce the work output of the machine, they increase the oil temperature, which in turn intensifies the cooling requirements of the machine. Since it takes power to drive the cooling fan, the energy consumption of the machine increases as well. This twofold loss in efficiency is like riding a bicycle uphill and also with a flat tire. 

Using energy efficient HYDREX XV gets you where you are going faster while using less energy, by increasing the hydraulic system flow rate and motor torque output, while reducing energy loss and consumption. On mobile equipment, this inevitably leads to reduced fuel consumption needed to drive the hydraulically controlled functions of the machine. These benefits are greatest when the machine is working hard and power is needed the most – at peak loads and elevated temperatures. In today’s business where heavy equipment is often being pushed to the limit, this creates a significant energy savings opportunity by selecting the right, high performance fluid.

Company info

2310 Lakeshore Road West
Mississauga, ON
CA, L5J 1K2

Website:
www.lubricants.petro-canada.ca

Read more

Related Articles